SlideShare ist ein Scribd-Unternehmen logo
1 von 48
Downloaden Sie, um offline zu lesen
04/05/14 1Hareesha N G, Asst. Prof, DSCE, BLore-78
UNIT-7: ACTUATORS:
Syllabus
• Types
• Characteristics of actuating system: weight, power-
to-weight ratio, operating pressure, stiffness vs.
compliance, Use of reduction gears
• comparison of hydraulic, electric, pneumatic
actuators
• Hydraulic actuators-proportional feedback control
• Electric motors: DC motors, Reversible AC motors,
Brushless DC motors
• Stepper motors- structure and principle of
operation, speed-torque characteristics
Introduction-Types
• Actuators are the muscles of robots.
• If you imagine that the links and the joints are the skeleton of
the robot, the actuators act as muscles, which move or rotate
the links to change the configuration of robots.
• The actuator must have enough power to accelerate and
decelerate the links and to carry the loads, be light, economical,
accurate, responsive, reliable, and easy to maintain.
• There are many types of actuators available.
– Electric motors
– Servomotors
– Stepper motors
– Direct-drive electric motors
– Hydraulic actuators
– Pneumatic actuators
– Shape memory metal actuators
– Magneto-strictive actuators
Introduction
• Electric motors — especially servomotors — are the most commonly
used robotic actuators.
• Hydraulic systems were very popular for large robots in the past and
are still around in many places, but are not used in new robots as
often any more.
• Direct drive electric motors, the shape memory metal type-actuators,
and others like them are mostly in research and development stage
and may become more useful in the near future.
CHARACTERISTICS OF ACTUATING SYSTEMS
Weight, Power-to-Weight Ratio, Operating Pressure
• It is important to consider the weight of the actuating system, as well
as its power-to-weight ratio.
• For example, the power-to-weight ratio of electric systems is
average.
• Stepper motors are generally heavier than servomotors for the same
power and thus have a lower power-to-weight ratio.
• The higher the voltage of an electric motor, the better power-to-
weight ratio it has.
• Pneumatic cylinders deliver the lowest power-to-weight ratio.
• Hydraulic systems have the highest power-to-weight ratio.
• However, it is important to realize that in these systems, the weight
is actually composed of two portions. One is the hydraulic actuator,
and the other is the hydraulic power unit.
• The system's power unit consists of a pump, which generates the
high pressure needed to operate the cylinders and rams, a reservoir,
filters, electric drive motors to drive the pump, cooling units, valves,
CHARACTERISTICS OF ACTUATING SYSTEMS
Weight, Power-to-Weight Ratio, Operating Pressure
• The actuators' role is only to move the joints.
• However, the power unit is normally stationary and located
somewhere away from the robot itself.
• The power is brought to the robot via an umbilical tether hose.
• Thus, the actual power-to-weight ratio of the cylinders is very high
for the moving parts.
• However, the power unit, which is very heavy, does not move and is
not counted in this ratio.
• If the power unit must also move with the robot, the total power-to-
weight ratio will be much less.
• The power that the hydraulic system delivers is also very high, due to
high operating pressures.
• This may range from 55 psi to 5,000 psi pressures. Pneumatic
cylinders normally operate around 100 to 120 psi.
• The higher pressures in hydraulic systems mean higher powers, but
they also require higher maintenance, and if a leak occurs, they can
become more dangerous.
Stiffness vs. Compliance
• Stiffness is the resistance of a material against deformation.
• It may be the stiffness of a beam against bending under the load, the
resistance of a gas against compression in a cylinder under load and
so on.
• The stiffer the system, the larger the load that is needed to deform it.
Conversely, the more compliant the system, the easier it deforms
under the load.
• Stiffness is directly related to the modulus of elasticity of the
material.
• The modulus of elasticity of fluids can be around 1 x 106
psi, which is
very high.
• As a result, hydraulic systems are very stiff and noncompliant.
Conversely, pneumatic systems are easily compressed, and, thus, are
compliant.
• Stiff systems have a more rapid response to changing loads and
pressures and are more accurate.
• Obviously, if a system is compliant, it can easily deform (or compress)
under changing load or changing driving force, and, thus, will be
inaccurate.
Stiffness vs. Compliance
• Similarly, if a small driving force is applied to a hydraulic ram, due to
its stiffness, it will respond more rapidly and more accurately than a
pneumatic system, which can deform under the same load.
• Additionally, the stiffer the system, the less it gives or deforms under
load, and thus the more accurately it holds its position.
• Now consider a robot that is used to insert an integrated circuit chip
into a circuit board.
• If the system is not stiff enough, the robot will not be able to push
the chip into the board, since the actuator may deform under the
resistive force.
• On the other hand, if the part and the holes are not perfectly aligned,
a stiff system cannot give enough to prevent damage to the robot or
the part, whereas a compliant system will give to prevent damage.
• So, although stiffness causes a more responsive and more accurate
system, it also creates a danger if all things are not always perfect.
• Thus, a working balance is needed between these two competing
characteristics.
Use of Reduction Gears
• Some systems, such as hydraulic devices, produce very large forces
with short strokes.
• This means that the hydraulic ram may be moved very slightly while
delivering its full force.
• As a result, there is no need to use reduction gear trains to increase
the torque it produces and to slow it down to manageable speeds.
• For this reason, hydraulic actuators can be directly attached to the
links, which simplifies the design, reduces the weight and cost and
rotating inertia of joints, reduces backlash, increases the reliability of
the system, due to simpler design and fewer parts, and also reduces
noise.
• On the other hand, electric motors rotate at high speeds (up to many
thousands of revolutions per minute) and must be used in
conjunction with reduction gears to increase their torque and to
decrease their speed, as no one would want a robot arm to be
rotating at such speeds.
• This, of course, increases the cost, number of parts, backlash, inertia
of the rotating body, etc., as was mentioned earlier, but also
increases the resolution of the system, as it is possible to rotate the
link a very small angle.
Actuators
• So, the motor will only "feel" a fraction of the actual inertia of the
load (which in the case of a robot, constitutes both the manipulator
and the load it carries with it)
Actuators
Actuators
Actuators
Actuators
Actuators
Hydraulic Actuators
• Hydraulic systems and actuators offer a high power-to-weight ratio, large
forces at low speeds (both linear and rotary actuation) compatibility with
microprocessor and electronic controls, and tolerance of extreme
hazardous environments.
• However, due to leakage problems, which is almost inevitable in hydraulic
systems, and due to their power unit weight and cost, they are not used
any more.
• Nowadays, most robots are electric. However, there are still many robots in
industry that have hydraulic actuators.
• Additionally, for special applications such as very large robots and civil
service robots, hydraulic actuators may be the appropriate choice.
• The total force that a linear cylinder can deliver can be tremendously large
for its size.
• A hydraulic cylinder can deliver a force of F = p x A lb, where A is the
effective area of the piston or ram and p is the working pressure.
• For example, for a pressure of 1.000 psi, every square inch of the cylinder
develops 1.000-lb of force.
• In rotary cylinders, the same principle is true, except that the output
is a torque where:
• where dx is the desired displacement and dx/dt is the desired velocity
of the piston.
• As you can see, by controlling the volume of the fluid going into the
cylinder the total displacement can be controlled.
• By controlling the rate in which the fluid is sent to the cylinder, the
velocity can be controlled.
• This is done through a 'servo-valve’ that controls the volume of the
fluid, as well its rate.
A hydraulic system generally consists of the following parts:
1. Hydraulic linear or rotary cylinders and rams. These provide the force
or torque needed to move the joints and are controlled by the servo
valves or manual valves.
2. A hydraulic pump which is a high-pressure pump that provides high-
pressure fluid to the system.
3. Electric (or others such as diesel engine) motor, which operates the
hydraulic pump.
4. Cooling system, which rids the system of the heat generated. In some
systems, in addition to cooling fans, radiators and cooled air are
used.
5. Reservoir, which keeps the fluid supply available to the system. Since
the pump is constantly supplying pressure to the system, whether or
not the system is using it, all the extra pressurized fluid, as well as all
the returned fluid from the cylinders, flow back into the reservoir.
A hydraulic system generally consists of the following parts:
6. Servo-valve is a very sensitive valve that controls the amount and the
rate of fluid to the cylinders. The servo-valve is generally driven by a
hydraulic servomotor.
7. Safety check valves, holding valves, and other safety valves
throughout the system.
8. Connecting hoses, which are used to transport the pressurized fluid
to the cylinders and back to the reservoir.
9. Sensors, which are used to control the motion of the cylinders. They
include position, velocity, magnetic, touch, and other sensors.
Actuators
HYDRAULIC POWER TRANSMISSION
LINEAR ACTUATOR
ROTARY ACTUATOR
LOADPUMP
PUMP
PISTON & ROD
TO RESERVOIR
HYDRO MOTOR
24
Limited-Rotation
Hydraulic Actuators
• Rack-and-pinion limited rotation actuator
© Goodheart-Willcox Co., Inc.
Permission granted to reproduce for
educational use only.
25
Limited-Rotation
Hydraulic Actuators
• Vane limited-rotation actuator
THE LIMITED ANGLE ROTARY ACTUATOR:
• The limited angle rotary actuator is applied when the shaft has to rotate over a
limited angle.
• The animation shows how this simple actuator works: in this case the shaft can
rotate over an angle of about 270 degrees.
• This type of actuator is, among others, used as a rotator actuator on (small) cranes
and excavators.
• Figure is a schematic drawing of a typical hydraulic
system.
• Figure is a schematic drawing of a position control pilot valve for a
hydraulic cylinder, also called a spool valve.
• This is a balanced valve, which means that the pressures on the two
sides of the spool are equal. Thus, it takes very little force to move
the spool even though it may be under very high pressures.
• When a servomotor is attached to the spool valve to operate it, a
servo-valve is created. The servo valve and the cylinder together
form a hydraulic servomotor.
As the spool moves up or
down, it opens the supply
and return ports through
which the fluid travels to
the cylinder or is returned
to the reservoir.
• Depending on the size of the opening of the port, the supply fluid
flow rate is controlled, and so is the velocity of the cylinder.
• Depending on the length of time that the port is kept open, the total
amount of the fluid to the cylinder, and thus its total travel, is
controlled.
• The command to the servomotor controlling the spool valve comes
from the controller.
• The controller sets the current to the servomotor, as well as the
duration the current is applied, which, in turn, controls the position
of the spool.
• Thus, for a robot, when the controller has calculated how much and
how fast a joint must move, it sets the current and its duration to the
servomotor, which, in turn, controls the position and rate of
movement of the spool valve, which, in turn, controls the flow of the
fluid and its rate to the cylinder, which moves the joint.
• Thesensors provide feedback to the controller for accurate and
continued control.
• Figure shows the flow of the fluid as the spool valve moves up or
down.
• As you can see, a simple motion of the spool controls the motion of
the cylinder.
• To provide feedback to the servo-valve, either electronic or
mechanical feedback can be added to the valve. (Otherwise, it will
not be a servo-valve, but a manual spool valve).
• Figure shows a simple mechanical feedback loop.
• A similar design is used in a two-stage spool valve to provide
feedback to the valve.
• Figure shows the schematic of the, block diagram
for the feedback loop.
ELECTRIC MOTORS
• When a wire carrying a current is placed within a magnetic field, it experiences a
force normal to the plane formed by the magnetic field.
• If the wire is attached to a center of rotation, the resulting torque will cause it to
rotate about the center of rotation.
• Changing the direction of the magnetic field or the current causes the wire to
continuously rotate about the center of rotation, as shown in Figure .
• In practice, to accomplish this change in the current, either a set of commutators
and brushes are used for DC motors, the current is electronically switched for DC
brushless motors, or AC current is used for AC motors.
This is the basic principle behind all
electric motors.
Similarly, if a conductor is moved within a
magnetic field crossing the flux, a current
develops through the conductor. This is
called a generator.
Figure: When a wire carrying a current is
placed within a magnetic field it will
experience a force in a direction normal to a
plane formed by the current and the field.
Actuators
• There are many types of electric motors that are used
in robotics. They include the following:
– DC motors
– reversible AC motors
– brushless DC motors
– stepper motors
• Except for stepper motors, all other types of motors
can be used as a servomotor.
• In each case, the torque or power output of the motor
is a function of the strength of the magnetic fields and
the current in the windings.
• Some motors have permanent magnets (PMs). These
motors generate less heat, since the field is always
present and no current is needed to build them.
• Others have a soft iron core and windings, where an
electric current creates the magnetic field.
• In this case, more heat is generated, but when needed, the
magnetic field can be varied by changing the current,
whereas in permanent magnet motors, the field is
constant.
• Additionally, under certain conditions, it is possible that the
permanent magnet may get damaged and lose its field
strength, in which case the motor becomes useless.
• For example, you should never take a motor apart, as the
permanent magnet will become significantly weaker.
• This is because the iron mass around the magnet holds the
field intact until they are separated.
• To increase the strength of the permanent magnets in
motors, most manufacturers magnetize the magnets
after assembling the motor. Motors without
permanent magnets do not have this problem.
• One important issue in the design and operation of all
motors is the dissipation of heat.
• As with the heat generated in many other devices, the
generated heat in motors eventually becomes the
deciding factor about its size and power.
• The heat is generated primarily from the resistance of
the wiring to electric current (load related), but
includes heat due to iron losses, including eddy current
losses and hysteresis losses, friction losses, brush
losses, and short-out circuit losses (speed related) as
well.
• The higher the current, the more heat is generated, as W = RI2
.
• Thicker wires generate less heat, but are more expensive, are heavier
(more inertia), and require more space.
• All motors generate some heat. However, what is important is the
path that the heat must take to leave the motor since if the heat is
dissipated faster, more generated heat can be dissipated before
damage occurs.
• Figure shows the heat leakage path to the environment for an AC-
type motor and a DC-type motor.
• In DC-type motors, the rotor contains the winding and
carries the current, and thus, heat is generated in the rotor.
• This heat must go from the rotor, through the air gap,
through the permanent magnets, through the motor's
body, and be dissipated into the environment.
• As you know, air is a very good isolator. Thus, the total heat
transfer coefficient for the DC motor is relatively low.
• On the other hand, in an AC-type motor, the rotor is a
permanent magnet, and the winding is in the stator.
• The generated heat in the stator is dissipated to the air by
conduction through the motor's body.
• As a result, the total heat transfer coefficient is relatively
high, especially because no air gap exists.
• As a result, AC-type motors can be exposed to relatively
higher currents without damage, and thus they are
generally more powerful for the same size.
• Stepper motors, although not AC motors, have a similar
construction; the rotor is a permanent magnet, and the
stator contains the windings. Thus, stepper motors have
good heat dissipation capability.
• Of course, another major factor in the difference between
brushed and brush-less motors is the life of the brushes
and commutators, as well as the physical limitation of
mechanical switching by brushes.
• Brushless DC motors, AC motors, and stepper motors are
all brushless, and thus they and are sturdy and generally
have long life (only limited by the life of rotor bearings).
DC Motors
• DC motors are very common in industry and have been used for a
long time. As a result, they are reliable, sturdy, and relatively
powerful.
• In DC motors, the stator is a set of fixed permanent magnets,
creating a fixed magnetic field, while the rotor carries a current.
• Through brushes and commutators, the direction of current is
changed continuously, causing the rotor to rotate continuously.
• Conversely, if the rotor is rotated within the magnetic field, a DC
current will develop, and the motor will act as a generator.
• If permanent magnets are used to generate the magnetic field, the
output torque TM is proportional to the magnetic flux φ and the
current in the rotor windings Irotor , Then,
• where kt is a constant. Since in permanent magnets, the flux is constant, the
output torque becomes a function of /rolor, and to control the output toque, /
(or corresponding voltage) must be changed. If instead of permanent
magnets, soft iron cores with windings are used for the stator as well, then
the output torque is a function of currents in both the rotor and the stator
windings:
• Here both k, and kfarz constants.
• Through the use of powerful magnets made of rare earth materials
and.alloys, the performance of motors has been improved significantly. As a
result, the power-to-weight ratio of motors is much better than before, and
they have replaced almost all other types of actuators.
• To overcome the problem of high inertia and large size of many electric
motors, a disk or shell motor can be used. In disk and shell motors, the iron
core of the rotor winding is removed to reduce its weight and inertia, and
as a result, these motors are capable of producing very large accelerations
(zero to 2,000 rpm in one ms [3]); they respond very favorably to changing
currents for control purposes. A shell motor's rotor looks similar to a
regular DC rotor without the massive iron core. However, in a disk motor,
the rotor is a flat, thin, plate, with windings pressed (etched) into it, as if
one would flatten a rotor into a disk. The wires are generally cut out of a
copper plate and embedded into a disk. The permanent magnets are
• generally small, short cylindrical magnets that are
placed on the two sides of the disk. As a result, disk
motors are very thin and are used in many
applications where both space and acceleration
requirements are important. Figure 6.15 is a
schematic of a disk motor.
Figure 6.15 Schematic of a disk motor. The
rotor has no iron core and thus has very little
inertia. As a result, it can accelerate and
decelerate very quickly.
Actuators
Actuators
Actuators
Actuators
Actuators

Weitere ähnliche Inhalte

Was ist angesagt?

Velocity sensors in_robotics
Velocity sensors in_roboticsVelocity sensors in_robotics
Velocity sensors in_roboticsManish Dhiman
 
Robotics and automation _ power sources and sensors
Robotics and automation _  power sources and sensorsRobotics and automation _  power sources and sensors
Robotics and automation _ power sources and sensorsJAIGANESH SEKAR
 
Robotics and machine vision system
Robotics and machine vision systemRobotics and machine vision system
Robotics and machine vision systemGowsick Subramaniam
 
Fundamental of robotic manipulator
Fundamental of robotic manipulatorFundamental of robotic manipulator
Fundamental of robotic manipulatorsnkalepvpit
 
Robot programming
Robot programmingRobot programming
Robot programmingGopal Saini
 
Hydraulic and Pneumatic Drive System
Hydraulic and Pneumatic Drive SystemHydraulic and Pneumatic Drive System
Hydraulic and Pneumatic Drive Systemturna67
 
ROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMING
ROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMINGROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMING
ROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMINGTAMILMECHKIT
 
Manipulator kinematics
Manipulator kinematicsManipulator kinematics
Manipulator kinematicsSudhir Reddy
 
Robotics and Automation basic concepts
Robotics and Automation   basic conceptsRobotics and Automation   basic concepts
Robotics and Automation basic conceptsJAIGANESH SEKAR
 
Introduction to robotics, Laws,Classification,Types, Drives,Geometry
Introduction to robotics, Laws,Classification,Types, Drives,Geometry  Introduction to robotics, Laws,Classification,Types, Drives,Geometry
Introduction to robotics, Laws,Classification,Types, Drives,Geometry Mohammad Ehtasham
 
Textual Robot programming
Textual Robot programmingTextual Robot programming
Textual Robot programmingCHEMGLOBE
 
ROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORSROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORSTAMILMECHKIT
 

Was ist angesagt? (20)

Velocity sensors in_robotics
Velocity sensors in_roboticsVelocity sensors in_robotics
Velocity sensors in_robotics
 
Robot Configuration - 2
Robot Configuration - 2Robot Configuration - 2
Robot Configuration - 2
 
Robotics and automation _ power sources and sensors
Robotics and automation _  power sources and sensorsRobotics and automation _  power sources and sensors
Robotics and automation _ power sources and sensors
 
Robotics and machine vision system
Robotics and machine vision systemRobotics and machine vision system
Robotics and machine vision system
 
Fundamental of robotic manipulator
Fundamental of robotic manipulatorFundamental of robotic manipulator
Fundamental of robotic manipulator
 
Robot programming
Robot programmingRobot programming
Robot programming
 
Electric drive systems in Robotics
Electric drive systems in RoboticsElectric drive systems in Robotics
Electric drive systems in Robotics
 
Grippers
GrippersGrippers
Grippers
 
Hydraulic and Pneumatic Drive System
Hydraulic and Pneumatic Drive SystemHydraulic and Pneumatic Drive System
Hydraulic and Pneumatic Drive System
 
Robot applications
Robot applicationsRobot applications
Robot applications
 
ROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMING
ROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMINGROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMING
ROBOTICS-ROBOT KINEMATICS AND ROBOT PROGRAMMING
 
sensors in robotics
sensors in roboticssensors in robotics
sensors in robotics
 
Unit-I Robotics
Unit-I RoboticsUnit-I Robotics
Unit-I Robotics
 
Manipulator kinematics
Manipulator kinematicsManipulator kinematics
Manipulator kinematics
 
Robotics and Automation basic concepts
Robotics and Automation   basic conceptsRobotics and Automation   basic concepts
Robotics and Automation basic concepts
 
Introduction to robotics, Laws,Classification,Types, Drives,Geometry
Introduction to robotics, Laws,Classification,Types, Drives,Geometry  Introduction to robotics, Laws,Classification,Types, Drives,Geometry
Introduction to robotics, Laws,Classification,Types, Drives,Geometry
 
Introduction to robotics
Introduction to roboticsIntroduction to robotics
Introduction to robotics
 
Textual Robot programming
Textual Robot programmingTextual Robot programming
Textual Robot programming
 
ROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORSROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORS
 
Robot Classification
Robot ClassificationRobot Classification
Robot Classification
 

Andere mochten auch (13)

Industrial Control Systems - Hydraulic Systems
Industrial Control Systems - Hydraulic SystemsIndustrial Control Systems - Hydraulic Systems
Industrial Control Systems - Hydraulic Systems
 
Class 29 pi, pd and pid pneumatic controllers
Class 29   pi, pd and pid pneumatic controllersClass 29   pi, pd and pid pneumatic controllers
Class 29 pi, pd and pid pneumatic controllers
 
Unitization
UnitizationUnitization
Unitization
 
International transportation and Supply chain
International transportation and Supply chainInternational transportation and Supply chain
International transportation and Supply chain
 
Logistics transportation
Logistics transportationLogistics transportation
Logistics transportation
 
Presentation on eco friendly packaging materials
Presentation on eco friendly packaging materialsPresentation on eco friendly packaging materials
Presentation on eco friendly packaging materials
 
Order processing
Order processingOrder processing
Order processing
 
Actuators.ppt
Actuators.pptActuators.ppt
Actuators.ppt
 
Transportation ppt of suppy chain management
Transportation ppt of suppy chain managementTransportation ppt of suppy chain management
Transportation ppt of suppy chain management
 
Transport
TransportTransport
Transport
 
Controlling 2 ppt
Controlling 2 pptControlling 2 ppt
Controlling 2 ppt
 
Control process
Control processControl process
Control process
 
Sensors
SensorsSensors
Sensors
 

Ähnlich wie Actuators

53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdfcbecuk23
 
vinay kumar actuators report
vinay kumar   actuators reportvinay kumar   actuators report
vinay kumar actuators reportAkash Maurya
 
unit-vii-feed-back-components.pptx
unit-vii-feed-back-components.pptxunit-vii-feed-back-components.pptx
unit-vii-feed-back-components.pptxParnerTehsil
 
MCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptxMCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptxDavidPeaceAchebe
 
lecture-1.ppt
lecture-1.pptlecture-1.ppt
lecture-1.pptpiko19
 
An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems Leonardo ENERGY
 
Introduction to hydraulics and pneumatic by Varun Pratap Singh
Introduction to hydraulics and pneumatic by Varun Pratap SinghIntroduction to hydraulics and pneumatic by Varun Pratap Singh
Introduction to hydraulics and pneumatic by Varun Pratap SinghVarun Pratap Singh
 
Kinetic Energy Recovery System
Kinetic Energy Recovery SystemKinetic Energy Recovery System
Kinetic Energy Recovery SystemAnkit Singh
 
PECD ELECRICAL DRIVES dddddddddddddddddd
PECD ELECRICAL DRIVES ddddddddddddddddddPECD ELECRICAL DRIVES dddddddddddddddddd
PECD ELECRICAL DRIVES ddddddddddddddddddAjayKumarSingh711098
 
Robot Drives And End Effectors.pptx
Robot Drives And End Effectors.pptxRobot Drives And End Effectors.pptx
Robot Drives And End Effectors.pptxtaruian
 
! Vehicles Hydraulic And Pneumatic Systems.ppt
! Vehicles Hydraulic And Pneumatic Systems.ppt! Vehicles Hydraulic And Pneumatic Systems.ppt
! Vehicles Hydraulic And Pneumatic Systems.pptأحمد دعبس
 
Presentation 9.pptx
Presentation 9.pptxPresentation 9.pptx
Presentation 9.pptxjagannathps3
 
Applications of fluid hydraulics
Applications of fluid hydraulicsApplications of fluid hydraulics
Applications of fluid hydraulicssumitlakhera
 

Ähnlich wie Actuators (20)

53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
 
Mine mechanisation 1
Mine mechanisation 1Mine mechanisation 1
Mine mechanisation 1
 
MEKATRONIKA Aktuator.pptx
MEKATRONIKA Aktuator.pptxMEKATRONIKA Aktuator.pptx
MEKATRONIKA Aktuator.pptx
 
vinay kumar actuators report
vinay kumar   actuators reportvinay kumar   actuators report
vinay kumar actuators report
 
unit-vii-feed-back-components.pptx
unit-vii-feed-back-components.pptxunit-vii-feed-back-components.pptx
unit-vii-feed-back-components.pptx
 
MCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptxMCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptx
 
Pump and pumping system
Pump and pumping systemPump and pumping system
Pump and pumping system
 
lecture-1.ppt
lecture-1.pptlecture-1.ppt
lecture-1.ppt
 
lecture-1.ppt
lecture-1.pptlecture-1.ppt
lecture-1.ppt
 
lecture-1.ppt
lecture-1.pptlecture-1.ppt
lecture-1.ppt
 
An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems
 
Introduction to hydraulics and pneumatic by Varun Pratap Singh
Introduction to hydraulics and pneumatic by Varun Pratap SinghIntroduction to hydraulics and pneumatic by Varun Pratap Singh
Introduction to hydraulics and pneumatic by Varun Pratap Singh
 
Kinetic Energy Recovery System
Kinetic Energy Recovery SystemKinetic Energy Recovery System
Kinetic Energy Recovery System
 
PECD ELECRICAL DRIVES dddddddddddddddddd
PECD ELECRICAL DRIVES ddddddddddddddddddPECD ELECRICAL DRIVES dddddddddddddddddd
PECD ELECRICAL DRIVES dddddddddddddddddd
 
Pdc
PdcPdc
Pdc
 
Robot Drives And End Effectors.pptx
Robot Drives And End Effectors.pptxRobot Drives And End Effectors.pptx
Robot Drives And End Effectors.pptx
 
! Vehicles Hydraulic And Pneumatic Systems.ppt
! Vehicles Hydraulic And Pneumatic Systems.ppt! Vehicles Hydraulic And Pneumatic Systems.ppt
! Vehicles Hydraulic And Pneumatic Systems.ppt
 
Presentation 9.pptx
Presentation 9.pptxPresentation 9.pptx
Presentation 9.pptx
 
Hydraulics
HydraulicsHydraulics
Hydraulics
 
Applications of fluid hydraulics
Applications of fluid hydraulicsApplications of fluid hydraulics
Applications of fluid hydraulics
 

Mehr von Hareesha N Gowda, Dayananda Sagar College of Engg, Bangalore

Mehr von Hareesha N Gowda, Dayananda Sagar College of Engg, Bangalore (20)

Alumni Meet Invitation.pdf
Alumni Meet Invitation.pdfAlumni Meet Invitation.pdf
Alumni Meet Invitation.pdf
 
Brammadevarahalli GP Panchapayana
Brammadevarahalli GP PanchapayanaBrammadevarahalli GP Panchapayana
Brammadevarahalli GP Panchapayana
 
Introduction to control systems
Introduction to control systemsIntroduction to control systems
Introduction to control systems
 
Be project report template
Be project report templateBe project report template
Be project report template
 
Computer aided machine drawing manual
Computer aided machine drawing manualComputer aided machine drawing manual
Computer aided machine drawing manual
 
Unit 1- simple stress and strain
Unit 1- simple stress and strainUnit 1- simple stress and strain
Unit 1- simple stress and strain
 
Unit 8: Torsion of circular shafts and elastic stability of columns
Unit 8: Torsion of circular shafts and elastic stability of columnsUnit 8: Torsion of circular shafts and elastic stability of columns
Unit 8: Torsion of circular shafts and elastic stability of columns
 
Unit 6: Bending and shear Stresses in beams
Unit 6: Bending and shear Stresses in beamsUnit 6: Bending and shear Stresses in beams
Unit 6: Bending and shear Stresses in beams
 
Unit 5 shear force and bending moment in beams
Unit 5  shear force and bending moment in beamsUnit 5  shear force and bending moment in beams
Unit 5 shear force and bending moment in beams
 
Unit 3 Compound stresses
Unit 3  Compound stressesUnit 3  Compound stresses
Unit 3 Compound stresses
 
Unit 2 stresses in composite sections
Unit 2  stresses in composite sectionsUnit 2  stresses in composite sections
Unit 2 stresses in composite sections
 
Dynamics of Machines: Question bank unitwise from vtu old question papers
Dynamics of Machines: Question bank unitwise from vtu old question papersDynamics of Machines: Question bank unitwise from vtu old question papers
Dynamics of Machines: Question bank unitwise from vtu old question papers
 
Mechanics of Materials: Question Bank from old VTU Question papers
Mechanics of Materials: Question Bank from old VTU Question papersMechanics of Materials: Question Bank from old VTU Question papers
Mechanics of Materials: Question Bank from old VTU Question papers
 
Robots: state of-the-art and future trends
Robots: state of-the-art and future trendsRobots: state of-the-art and future trends
Robots: state of-the-art and future trends
 
Screw thread measurements and Gear measurement
Screw thread measurements and Gear measurementScrew thread measurements and Gear measurement
Screw thread measurements and Gear measurement
 
Force, Pressure and Torque measurements
Force, Pressure and Torque measurementsForce, Pressure and Torque measurements
Force, Pressure and Torque measurements
 
Mechanical measurements and Measurement systems
Mechanical measurements and Measurement systemsMechanical measurements and Measurement systems
Mechanical measurements and Measurement systems
 
CIM and automation laboratory manual
CIM and automation laboratory manualCIM and automation laboratory manual
CIM and automation laboratory manual
 
Introduction to Non-Traditional Machining
Introduction to Non-Traditional MachiningIntroduction to Non-Traditional Machining
Introduction to Non-Traditional Machining
 
Chemical machining
Chemical machiningChemical machining
Chemical machining
 

Kürzlich hochgeladen

Gender Bias in Engineer, Honors 203 Project
Gender Bias in Engineer, Honors 203 ProjectGender Bias in Engineer, Honors 203 Project
Gender Bias in Engineer, Honors 203 Projectreemakb03
 
Basic Principle of Electrochemical Sensor
Basic Principle of  Electrochemical SensorBasic Principle of  Electrochemical Sensor
Basic Principle of Electrochemical SensorTanvir Moin
 
Technology Features of Apollo HDD Machine, Its Technical Specification with C...
Technology Features of Apollo HDD Machine, Its Technical Specification with C...Technology Features of Apollo HDD Machine, Its Technical Specification with C...
Technology Features of Apollo HDD Machine, Its Technical Specification with C...Apollo Techno Industries Pvt Ltd
 
Transforming Process Safety Management: Challenges, Benefits, and Transition ...
Transforming Process Safety Management: Challenges, Benefits, and Transition ...Transforming Process Safety Management: Challenges, Benefits, and Transition ...
Transforming Process Safety Management: Challenges, Benefits, and Transition ...soginsider
 
GENERAL CONDITIONS FOR CONTRACTS OF CIVIL ENGINEERING WORKS
GENERAL CONDITIONS  FOR  CONTRACTS OF CIVIL ENGINEERING WORKS GENERAL CONDITIONS  FOR  CONTRACTS OF CIVIL ENGINEERING WORKS
GENERAL CONDITIONS FOR CONTRACTS OF CIVIL ENGINEERING WORKS Bahzad5
 
A Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software SimulationA Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software SimulationMohsinKhanA
 
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxSUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxNaveenVerma126
 
Graphics Primitives and CG Display Devices
Graphics Primitives and CG Display DevicesGraphics Primitives and CG Display Devices
Graphics Primitives and CG Display DevicesDIPIKA83
 
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...Amil baba
 
Phase noise transfer functions.pptx
Phase noise transfer      functions.pptxPhase noise transfer      functions.pptx
Phase noise transfer functions.pptxSaiGouthamSunkara
 
Clutches and brkesSelect any 3 position random motion out of real world and d...
Clutches and brkesSelect any 3 position random motion out of real world and d...Clutches and brkesSelect any 3 position random motion out of real world and d...
Clutches and brkesSelect any 3 position random motion out of real world and d...sahb78428
 
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdfsdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdfJulia Kaye
 
Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...
Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...
Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...Sean Meyn
 
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptxVertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptxLMW Machine Tool Division
 
ASME BPVC 2023 Section I para leer y entender
ASME BPVC 2023 Section I para leer y entenderASME BPVC 2023 Section I para leer y entender
ASME BPVC 2023 Section I para leer y entenderjuancarlos286641
 
How to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdfHow to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdfRedhwan Qasem Shaddad
 
Guardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSecGuardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSecTrupti Shiralkar, CISSP
 

Kürzlich hochgeladen (20)

Lecture 2 .pdf
Lecture 2                           .pdfLecture 2                           .pdf
Lecture 2 .pdf
 
Présentation IIRB 2024 Marine Cordonnier.pdf
Présentation IIRB 2024 Marine Cordonnier.pdfPrésentation IIRB 2024 Marine Cordonnier.pdf
Présentation IIRB 2024 Marine Cordonnier.pdf
 
Gender Bias in Engineer, Honors 203 Project
Gender Bias in Engineer, Honors 203 ProjectGender Bias in Engineer, Honors 203 Project
Gender Bias in Engineer, Honors 203 Project
 
Basic Principle of Electrochemical Sensor
Basic Principle of  Electrochemical SensorBasic Principle of  Electrochemical Sensor
Basic Principle of Electrochemical Sensor
 
Technology Features of Apollo HDD Machine, Its Technical Specification with C...
Technology Features of Apollo HDD Machine, Its Technical Specification with C...Technology Features of Apollo HDD Machine, Its Technical Specification with C...
Technology Features of Apollo HDD Machine, Its Technical Specification with C...
 
Transforming Process Safety Management: Challenges, Benefits, and Transition ...
Transforming Process Safety Management: Challenges, Benefits, and Transition ...Transforming Process Safety Management: Challenges, Benefits, and Transition ...
Transforming Process Safety Management: Challenges, Benefits, and Transition ...
 
GENERAL CONDITIONS FOR CONTRACTS OF CIVIL ENGINEERING WORKS
GENERAL CONDITIONS  FOR  CONTRACTS OF CIVIL ENGINEERING WORKS GENERAL CONDITIONS  FOR  CONTRACTS OF CIVIL ENGINEERING WORKS
GENERAL CONDITIONS FOR CONTRACTS OF CIVIL ENGINEERING WORKS
 
A Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software SimulationA Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software Simulation
 
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxSUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
 
Graphics Primitives and CG Display Devices
Graphics Primitives and CG Display DevicesGraphics Primitives and CG Display Devices
Graphics Primitives and CG Display Devices
 
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
 
Phase noise transfer functions.pptx
Phase noise transfer      functions.pptxPhase noise transfer      functions.pptx
Phase noise transfer functions.pptx
 
Clutches and brkesSelect any 3 position random motion out of real world and d...
Clutches and brkesSelect any 3 position random motion out of real world and d...Clutches and brkesSelect any 3 position random motion out of real world and d...
Clutches and brkesSelect any 3 position random motion out of real world and d...
 
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdfsdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
 
Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...
Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...
Quasi-Stochastic Approximation: Algorithm Design Principles with Applications...
 
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptxVertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
 
ASME BPVC 2023 Section I para leer y entender
ASME BPVC 2023 Section I para leer y entenderASME BPVC 2023 Section I para leer y entender
ASME BPVC 2023 Section I para leer y entender
 
How to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdfHow to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdf
 
Guardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSecGuardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSec
 
Présentation IIRB 2024 Chloe Dufrane.pdf
Présentation IIRB 2024 Chloe Dufrane.pdfPrésentation IIRB 2024 Chloe Dufrane.pdf
Présentation IIRB 2024 Chloe Dufrane.pdf
 

Actuators

  • 1. 04/05/14 1Hareesha N G, Asst. Prof, DSCE, BLore-78
  • 2. UNIT-7: ACTUATORS: Syllabus • Types • Characteristics of actuating system: weight, power- to-weight ratio, operating pressure, stiffness vs. compliance, Use of reduction gears • comparison of hydraulic, electric, pneumatic actuators • Hydraulic actuators-proportional feedback control • Electric motors: DC motors, Reversible AC motors, Brushless DC motors • Stepper motors- structure and principle of operation, speed-torque characteristics
  • 3. Introduction-Types • Actuators are the muscles of robots. • If you imagine that the links and the joints are the skeleton of the robot, the actuators act as muscles, which move or rotate the links to change the configuration of robots. • The actuator must have enough power to accelerate and decelerate the links and to carry the loads, be light, economical, accurate, responsive, reliable, and easy to maintain. • There are many types of actuators available. – Electric motors – Servomotors – Stepper motors – Direct-drive electric motors – Hydraulic actuators – Pneumatic actuators – Shape memory metal actuators – Magneto-strictive actuators
  • 4. Introduction • Electric motors — especially servomotors — are the most commonly used robotic actuators. • Hydraulic systems were very popular for large robots in the past and are still around in many places, but are not used in new robots as often any more. • Direct drive electric motors, the shape memory metal type-actuators, and others like them are mostly in research and development stage and may become more useful in the near future.
  • 5. CHARACTERISTICS OF ACTUATING SYSTEMS Weight, Power-to-Weight Ratio, Operating Pressure • It is important to consider the weight of the actuating system, as well as its power-to-weight ratio. • For example, the power-to-weight ratio of electric systems is average. • Stepper motors are generally heavier than servomotors for the same power and thus have a lower power-to-weight ratio. • The higher the voltage of an electric motor, the better power-to- weight ratio it has. • Pneumatic cylinders deliver the lowest power-to-weight ratio. • Hydraulic systems have the highest power-to-weight ratio. • However, it is important to realize that in these systems, the weight is actually composed of two portions. One is the hydraulic actuator, and the other is the hydraulic power unit. • The system's power unit consists of a pump, which generates the high pressure needed to operate the cylinders and rams, a reservoir, filters, electric drive motors to drive the pump, cooling units, valves,
  • 6. CHARACTERISTICS OF ACTUATING SYSTEMS Weight, Power-to-Weight Ratio, Operating Pressure • The actuators' role is only to move the joints. • However, the power unit is normally stationary and located somewhere away from the robot itself. • The power is brought to the robot via an umbilical tether hose. • Thus, the actual power-to-weight ratio of the cylinders is very high for the moving parts. • However, the power unit, which is very heavy, does not move and is not counted in this ratio. • If the power unit must also move with the robot, the total power-to- weight ratio will be much less. • The power that the hydraulic system delivers is also very high, due to high operating pressures. • This may range from 55 psi to 5,000 psi pressures. Pneumatic cylinders normally operate around 100 to 120 psi. • The higher pressures in hydraulic systems mean higher powers, but they also require higher maintenance, and if a leak occurs, they can become more dangerous.
  • 7. Stiffness vs. Compliance • Stiffness is the resistance of a material against deformation. • It may be the stiffness of a beam against bending under the load, the resistance of a gas against compression in a cylinder under load and so on. • The stiffer the system, the larger the load that is needed to deform it. Conversely, the more compliant the system, the easier it deforms under the load. • Stiffness is directly related to the modulus of elasticity of the material. • The modulus of elasticity of fluids can be around 1 x 106 psi, which is very high. • As a result, hydraulic systems are very stiff and noncompliant. Conversely, pneumatic systems are easily compressed, and, thus, are compliant. • Stiff systems have a more rapid response to changing loads and pressures and are more accurate. • Obviously, if a system is compliant, it can easily deform (or compress) under changing load or changing driving force, and, thus, will be inaccurate.
  • 8. Stiffness vs. Compliance • Similarly, if a small driving force is applied to a hydraulic ram, due to its stiffness, it will respond more rapidly and more accurately than a pneumatic system, which can deform under the same load. • Additionally, the stiffer the system, the less it gives or deforms under load, and thus the more accurately it holds its position. • Now consider a robot that is used to insert an integrated circuit chip into a circuit board. • If the system is not stiff enough, the robot will not be able to push the chip into the board, since the actuator may deform under the resistive force. • On the other hand, if the part and the holes are not perfectly aligned, a stiff system cannot give enough to prevent damage to the robot or the part, whereas a compliant system will give to prevent damage. • So, although stiffness causes a more responsive and more accurate system, it also creates a danger if all things are not always perfect. • Thus, a working balance is needed between these two competing characteristics.
  • 9. Use of Reduction Gears • Some systems, such as hydraulic devices, produce very large forces with short strokes. • This means that the hydraulic ram may be moved very slightly while delivering its full force. • As a result, there is no need to use reduction gear trains to increase the torque it produces and to slow it down to manageable speeds. • For this reason, hydraulic actuators can be directly attached to the links, which simplifies the design, reduces the weight and cost and rotating inertia of joints, reduces backlash, increases the reliability of the system, due to simpler design and fewer parts, and also reduces noise. • On the other hand, electric motors rotate at high speeds (up to many thousands of revolutions per minute) and must be used in conjunction with reduction gears to increase their torque and to decrease their speed, as no one would want a robot arm to be rotating at such speeds. • This, of course, increases the cost, number of parts, backlash, inertia of the rotating body, etc., as was mentioned earlier, but also increases the resolution of the system, as it is possible to rotate the link a very small angle.
  • 11. • So, the motor will only "feel" a fraction of the actual inertia of the load (which in the case of a robot, constitutes both the manipulator and the load it carries with it)
  • 17. Hydraulic Actuators • Hydraulic systems and actuators offer a high power-to-weight ratio, large forces at low speeds (both linear and rotary actuation) compatibility with microprocessor and electronic controls, and tolerance of extreme hazardous environments. • However, due to leakage problems, which is almost inevitable in hydraulic systems, and due to their power unit weight and cost, they are not used any more. • Nowadays, most robots are electric. However, there are still many robots in industry that have hydraulic actuators. • Additionally, for special applications such as very large robots and civil service robots, hydraulic actuators may be the appropriate choice. • The total force that a linear cylinder can deliver can be tremendously large for its size. • A hydraulic cylinder can deliver a force of F = p x A lb, where A is the effective area of the piston or ram and p is the working pressure. • For example, for a pressure of 1.000 psi, every square inch of the cylinder develops 1.000-lb of force.
  • 18. • In rotary cylinders, the same principle is true, except that the output is a torque where:
  • 19. • where dx is the desired displacement and dx/dt is the desired velocity of the piston. • As you can see, by controlling the volume of the fluid going into the cylinder the total displacement can be controlled. • By controlling the rate in which the fluid is sent to the cylinder, the velocity can be controlled. • This is done through a 'servo-valve’ that controls the volume of the fluid, as well its rate.
  • 20. A hydraulic system generally consists of the following parts: 1. Hydraulic linear or rotary cylinders and rams. These provide the force or torque needed to move the joints and are controlled by the servo valves or manual valves. 2. A hydraulic pump which is a high-pressure pump that provides high- pressure fluid to the system. 3. Electric (or others such as diesel engine) motor, which operates the hydraulic pump. 4. Cooling system, which rids the system of the heat generated. In some systems, in addition to cooling fans, radiators and cooled air are used. 5. Reservoir, which keeps the fluid supply available to the system. Since the pump is constantly supplying pressure to the system, whether or not the system is using it, all the extra pressurized fluid, as well as all the returned fluid from the cylinders, flow back into the reservoir.
  • 21. A hydraulic system generally consists of the following parts: 6. Servo-valve is a very sensitive valve that controls the amount and the rate of fluid to the cylinders. The servo-valve is generally driven by a hydraulic servomotor. 7. Safety check valves, holding valves, and other safety valves throughout the system. 8. Connecting hoses, which are used to transport the pressurized fluid to the cylinders and back to the reservoir. 9. Sensors, which are used to control the motion of the cylinders. They include position, velocity, magnetic, touch, and other sensors.
  • 23. HYDRAULIC POWER TRANSMISSION LINEAR ACTUATOR ROTARY ACTUATOR LOADPUMP PUMP PISTON & ROD TO RESERVOIR HYDRO MOTOR
  • 25. © Goodheart-Willcox Co., Inc. Permission granted to reproduce for educational use only. 25 Limited-Rotation Hydraulic Actuators • Vane limited-rotation actuator
  • 26. THE LIMITED ANGLE ROTARY ACTUATOR: • The limited angle rotary actuator is applied when the shaft has to rotate over a limited angle. • The animation shows how this simple actuator works: in this case the shaft can rotate over an angle of about 270 degrees. • This type of actuator is, among others, used as a rotator actuator on (small) cranes and excavators.
  • 27. • Figure is a schematic drawing of a typical hydraulic system.
  • 28. • Figure is a schematic drawing of a position control pilot valve for a hydraulic cylinder, also called a spool valve. • This is a balanced valve, which means that the pressures on the two sides of the spool are equal. Thus, it takes very little force to move the spool even though it may be under very high pressures. • When a servomotor is attached to the spool valve to operate it, a servo-valve is created. The servo valve and the cylinder together form a hydraulic servomotor. As the spool moves up or down, it opens the supply and return ports through which the fluid travels to the cylinder or is returned to the reservoir.
  • 29. • Depending on the size of the opening of the port, the supply fluid flow rate is controlled, and so is the velocity of the cylinder. • Depending on the length of time that the port is kept open, the total amount of the fluid to the cylinder, and thus its total travel, is controlled. • The command to the servomotor controlling the spool valve comes from the controller. • The controller sets the current to the servomotor, as well as the duration the current is applied, which, in turn, controls the position of the spool. • Thus, for a robot, when the controller has calculated how much and how fast a joint must move, it sets the current and its duration to the servomotor, which, in turn, controls the position and rate of movement of the spool valve, which, in turn, controls the flow of the fluid and its rate to the cylinder, which moves the joint.
  • 30. • Thesensors provide feedback to the controller for accurate and continued control. • Figure shows the flow of the fluid as the spool valve moves up or down. • As you can see, a simple motion of the spool controls the motion of the cylinder.
  • 31. • To provide feedback to the servo-valve, either electronic or mechanical feedback can be added to the valve. (Otherwise, it will not be a servo-valve, but a manual spool valve). • Figure shows a simple mechanical feedback loop. • A similar design is used in a two-stage spool valve to provide feedback to the valve.
  • 32. • Figure shows the schematic of the, block diagram for the feedback loop.
  • 33. ELECTRIC MOTORS • When a wire carrying a current is placed within a magnetic field, it experiences a force normal to the plane formed by the magnetic field. • If the wire is attached to a center of rotation, the resulting torque will cause it to rotate about the center of rotation. • Changing the direction of the magnetic field or the current causes the wire to continuously rotate about the center of rotation, as shown in Figure . • In practice, to accomplish this change in the current, either a set of commutators and brushes are used for DC motors, the current is electronically switched for DC brushless motors, or AC current is used for AC motors. This is the basic principle behind all electric motors. Similarly, if a conductor is moved within a magnetic field crossing the flux, a current develops through the conductor. This is called a generator. Figure: When a wire carrying a current is placed within a magnetic field it will experience a force in a direction normal to a plane formed by the current and the field.
  • 35. • There are many types of electric motors that are used in robotics. They include the following: – DC motors – reversible AC motors – brushless DC motors – stepper motors • Except for stepper motors, all other types of motors can be used as a servomotor. • In each case, the torque or power output of the motor is a function of the strength of the magnetic fields and the current in the windings. • Some motors have permanent magnets (PMs). These motors generate less heat, since the field is always present and no current is needed to build them.
  • 36. • Others have a soft iron core and windings, where an electric current creates the magnetic field. • In this case, more heat is generated, but when needed, the magnetic field can be varied by changing the current, whereas in permanent magnet motors, the field is constant. • Additionally, under certain conditions, it is possible that the permanent magnet may get damaged and lose its field strength, in which case the motor becomes useless. • For example, you should never take a motor apart, as the permanent magnet will become significantly weaker. • This is because the iron mass around the magnet holds the field intact until they are separated.
  • 37. • To increase the strength of the permanent magnets in motors, most manufacturers magnetize the magnets after assembling the motor. Motors without permanent magnets do not have this problem. • One important issue in the design and operation of all motors is the dissipation of heat. • As with the heat generated in many other devices, the generated heat in motors eventually becomes the deciding factor about its size and power. • The heat is generated primarily from the resistance of the wiring to electric current (load related), but includes heat due to iron losses, including eddy current losses and hysteresis losses, friction losses, brush losses, and short-out circuit losses (speed related) as well.
  • 38. • The higher the current, the more heat is generated, as W = RI2 . • Thicker wires generate less heat, but are more expensive, are heavier (more inertia), and require more space. • All motors generate some heat. However, what is important is the path that the heat must take to leave the motor since if the heat is dissipated faster, more generated heat can be dissipated before damage occurs. • Figure shows the heat leakage path to the environment for an AC- type motor and a DC-type motor.
  • 39. • In DC-type motors, the rotor contains the winding and carries the current, and thus, heat is generated in the rotor. • This heat must go from the rotor, through the air gap, through the permanent magnets, through the motor's body, and be dissipated into the environment. • As you know, air is a very good isolator. Thus, the total heat transfer coefficient for the DC motor is relatively low. • On the other hand, in an AC-type motor, the rotor is a permanent magnet, and the winding is in the stator. • The generated heat in the stator is dissipated to the air by conduction through the motor's body. • As a result, the total heat transfer coefficient is relatively high, especially because no air gap exists.
  • 40. • As a result, AC-type motors can be exposed to relatively higher currents without damage, and thus they are generally more powerful for the same size. • Stepper motors, although not AC motors, have a similar construction; the rotor is a permanent magnet, and the stator contains the windings. Thus, stepper motors have good heat dissipation capability. • Of course, another major factor in the difference between brushed and brush-less motors is the life of the brushes and commutators, as well as the physical limitation of mechanical switching by brushes. • Brushless DC motors, AC motors, and stepper motors are all brushless, and thus they and are sturdy and generally have long life (only limited by the life of rotor bearings).
  • 41. DC Motors • DC motors are very common in industry and have been used for a long time. As a result, they are reliable, sturdy, and relatively powerful. • In DC motors, the stator is a set of fixed permanent magnets, creating a fixed magnetic field, while the rotor carries a current. • Through brushes and commutators, the direction of current is changed continuously, causing the rotor to rotate continuously. • Conversely, if the rotor is rotated within the magnetic field, a DC current will develop, and the motor will act as a generator. • If permanent magnets are used to generate the magnetic field, the output torque TM is proportional to the magnetic flux φ and the current in the rotor windings Irotor , Then,
  • 42. • where kt is a constant. Since in permanent magnets, the flux is constant, the output torque becomes a function of /rolor, and to control the output toque, / (or corresponding voltage) must be changed. If instead of permanent magnets, soft iron cores with windings are used for the stator as well, then the output torque is a function of currents in both the rotor and the stator windings: • Here both k, and kfarz constants. • Through the use of powerful magnets made of rare earth materials and.alloys, the performance of motors has been improved significantly. As a result, the power-to-weight ratio of motors is much better than before, and they have replaced almost all other types of actuators. • To overcome the problem of high inertia and large size of many electric motors, a disk or shell motor can be used. In disk and shell motors, the iron core of the rotor winding is removed to reduce its weight and inertia, and as a result, these motors are capable of producing very large accelerations (zero to 2,000 rpm in one ms [3]); they respond very favorably to changing currents for control purposes. A shell motor's rotor looks similar to a regular DC rotor without the massive iron core. However, in a disk motor, the rotor is a flat, thin, plate, with windings pressed (etched) into it, as if one would flatten a rotor into a disk. The wires are generally cut out of a copper plate and embedded into a disk. The permanent magnets are
  • 43. • generally small, short cylindrical magnets that are placed on the two sides of the disk. As a result, disk motors are very thin and are used in many applications where both space and acceleration requirements are important. Figure 6.15 is a schematic of a disk motor. Figure 6.15 Schematic of a disk motor. The rotor has no iron core and thus has very little inertia. As a result, it can accelerate and decelerate very quickly.