SlideShare ist ein Scribd-Unternehmen logo
1 von 18
Downloaden Sie, um offline zu lesen
Unit 2  stresses in composite sections
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 1
TABLE OF CONTENTS
TABLE OF CONTENTS 0
Syllabus 2
2.1. VOLUMETRIC STRAIN 2
2.2. EXPRESSION FOR VOLUMETRIC STRAIN 2
2.3. ELASTIC CONSTANTS 4
2.3.1 Young’s Modulus 4
2.3.2 Shear Modulus or Modulus of Rigidity 5
2.3.3 Bulk modulus 5
2.3.4 Relation among Elastic Constants 6
i) Relation between E, G and  6
ii) Relation between E, K and : 8
iii) Relation between E, G and K 8
iv) Relation between E, K and  9
2.4. TEMPERATURE STRESSES 9
Stress and Strain when the Supports Yield: 10
2.5. THERMAL STRESSES IN COMPOSITE BARS 11
2.6 WORKED EXAMPLES 13
REFERENCES: 17
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 2
UNIT 2:
STRESS IN COMPOSITE SECTION
Syllabus
Volumetric strain, expression for volumetric strain, elastic constants, simple shear stress, shear
strain, temperature stresses (including compound bars).
2.1. VOLUMETRIC STRAIN
The ratio of change in volume to the original volume of a body (when the body is subjected to a
single force or a system of forces) is called volumetric strain. It is denoted by εv.
Mathematically, volumetric strain is given by
V
V
v

 
Where
δV = Change in volume, and V = Original volume.
2.2. EXPRESSION FOR VOLUMETRIC STRAIN
Referring to Fig.2.1, the quantity εv represents the change in the volume per unit volume. It is
referred to as the dilation of the material. Consider a small rectangular element of dimensions x, y
and z subjected to three mutually perpendicular stresses.
Fig. 2.1 Rectangular element subjected to three mutually perpendicular stresses.
Original volume of the element is given by
V = xyz
Therefore, the total change in the volume
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 3
or
Referring to Fig.2.2, consider a bar/rod of length L and diameter d, then the volume of the bar is
given by
Fig.2.2. Volumetric strain in circular rod
Therefore,
Since V is the function of both d and L, dividing previous Eq. throughout by V, we get
Since,
We have,
Thus, the volumetric strain is the sum of the three mutually perpendicular linear strains. Since εv
represents a change in volume, it must be independent of the orientation of the element
considered. It follows that the quantities,
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 4
εx + εy + εz and ζx ζy and ζy
are also independent of the orientation of the element. Since,
εv = εx + εy + εz
2.3. ELASTIC CONSTANTS
Elastic constants arc those factors which determine the deformations produced by a given stress
system acting on a material. These factors (i.e. elastic constants) arc constant within the limits for
which Hooke's laws are obeyed. Various elastic constants are:
 Modulus of elasticity (E)
 Poisson's ratio (μ or ν or 1/m)
 Modulus of rigidity (G or N )
 Bulk modulus (K)
2.3.1 Young’s Modulus
When an axial stress σ (say, tensile) is applied along the longitudinal axis of a bar, the length of
the bar will be increased. This change in the length (usually called deformation) per unit length
of the bar, is termed as longitudinal strain (ε) or primary strain. This ratio of stress to strain,
within elastic limits, is called the modulus of elasticity (E):
Thus, modulus of elasticity (E) =ζ/ε
The modulus of elasticity (also called Young's modulus of elasticity) is the constant of
proportionality which is defined as the intensity of stress that causes unit strain.
Table 2.1 gives the values of modulus of elasticity (E) for some common materials.
S. N. Material Modulus of elasticity E
(kN/mm2 or GPa)
1 Aluminium (Pure) 70
2 Aluminium alloys 70 - 79
3 Brass 96 - 110
4 Bronze 96-120
5 Cast iron 83 - 170
6 Copper (Pure) 110 - 120
7 Steel 190 - 210
8 Wrought iron 190
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 5
2.3.2 Shear Modulus or Modulus of Rigidity
The shear modules or modulus of rigidity (also called the modulus of transverse elasticity)
expresses the relation between shear stress and shear strain. It has been found experimentally
that, within elastic limit, shear stress (τ) is proportional to the shear strain (γ)
Thus


G
Where G = modulus of rigidity
(Also sometimes denoted by symbol N or C)
Table 2.2 gives the values of modulus of rigidity for some common engineering materials.
Table 2.2. Values of modulus of rigidity
S.N. Material
Modulus of Rigidity
(KNmm2
or GPa)
1 Aluminium (Pure) 26
2 Aluminium alloys 26-30
3 Brass 36-41
4 Bronze 36-44
5 Cast iron 32 - 69
6 Copper (Pure) 40-47
7 Steel 75-80
8 Wrought iron 75
2.3.3 Bulk modulus
When a body is subjected to three mutually perpendicular like stresses of equal intensity (ζ), the ratio of
direct stress (σ) to the corresponding volumetric strain (εv ) is defined as the bulk modulus K for the
material of the body.
Thus ,
v


strainVolumetric
stressDirect
=Kmodulusbulk
The bulk modulus of elasticity K is defined only when three mutually perpendicular normal
stresses are equal, i.e.
σx = σy = σz = σ
The bulk modulus of elasticity is shown in Fig. 2.3.
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 6
Fig. 2.3: Bulk Modulus
2.3.4 Relation among Elastic Constants
i) Relation between E, G and 
Let us establish a relation among the elastic constants E, G and . Consider a cube of material of
side ‘a' subjected to the action of the shear and complementary shear stresses as shown in the Fig.
2.4 and producing the strained shape as shown in the figure below.
Assuming that the strains are small and the angle A C B may be taken as 450
.
Fig. 2.4
Therefore strain on the diagonal OA = Change in length / original length
Since angle between OA and OB is very small hence OA  OB therefore BC, is the change in the
length of the diagonal OA
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 7
Now this shear stress system is equivalent or can be replaced by a system of direct stresses at
450
as shown in Fig. 2.5. One set will be compressive, the other tensile, and both will be equal in
value to the applied shear strain.
Fig. 2.5
Thus, for the direct state of stress system which applies along the diagonals:
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 8
ii) Relation between E, K and :
Consider a cube subjected to three equal stresses  as shown in the Fig.2.6
Fig.2.6
The total strain in one direction or along one edge due to the application of hydrostatic stress or
volumetric stress  is given as
iii) Relation between E, G and K
The relationship between E, G and K can be easily determined by eliminating  from the already
derived relations.
i.e.,
E = 2 G (1 + ) and E = 3 K (1  )
Thus, the following relationship may be obtained
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 9
iv) Relation between E, K and 
From the already derived relations, E can be eliminated
2.4. TEMPERATURE STRESSES
Thermal stresses are the stresses induced in a body due to change in temperature. Thermal
stresses are set up in a body, when the temperature of the body is raised or lowered and the body
is not allowed to expand or contract freely. But if the body is allowed to expand or contract
freely, no stresses will be set up in the body.
Consider a body which is heated to a certain temperature.
Let
L = Original length of the body,
T = Rise in temperature,
E = Young's Modulus,
 = Co-efficient of linear expansion,
dL = Extension of rod due to rise of temperature.
If the rod is free to expand, then extension of the rod is given by
dL = .T.L
This is shown in Fig. 2.7 (a) in which AB represents the original length and BB' represents the
increase in length due to temperature rise. Now suppose that an external compressive load, P is
applied at B' so that the rod is decreased in its length from (L + .T.L) to L as shown in Figs. (b)
and (c).
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 10
Fig. 2.7: Thermal stresses
And load or thrust on the rod = Stress x Area = .T.E x A
If the ends of the body are fixed to rigid supports, so that its expansion is prevented, then
compressive stress and strain will be set up in the rod. These stresses and strains are known as
thermal stresses and thermal strain.
Thermal stress is also known as temperature stress. And thermal strain is also known as
temperature strain.
Stress and Strain when the Supports Yield:
If the supports yield by an amount equal to , then the actual expansion
= Expansion due to rise in temperature -  = .T.L - 
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 11
2.5. THERMAL STRESSES IN COMPOSITE BARS
Fig. 2.8 (a) shows a composite bar consisting of two members, a bar of brass and another of steel.
Let the composite bar be heated through some temperature. If the members are free to expand
then no stresses will be induced in the members. But the two members are rigidly fixed and
hence the composite bar as a whole will expand by the same amount. As the co-efficient of linear
expansion of brass is more than that of the steel, the brass will expand more than the steel. Hence
the free expansion of brass will be more than that of the steel. But both the members are not free
to expand, and hence the expansion of the composite bar, as a whole, will be less than that of the
brass, but more than that of the steel. Hence the stress induced in the brass will be compressive
whereas the stress in steel will be tensile as shown in Fig. 2.8 (c). Hence the load or force on the
brass will be compressive whereas on the steel the load will be tensile.
Let
Ab = Area of cross-section of brass bar
σb = Stress in brass
b = Strain in brass
b = Co-efficient of linear expansion for brass
Eb = Young’s modulus for copper
As, s, s, s = Corresponding values of area, stress, strain and co-efficient of linear expansion for
steel, and
Es = Young's modulus for steel.
 = Actual expansion of the composite bar
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 12
Now load on the brass = Stress in brass x Area of brass= b x Ab
And load on the steel = Stress in brass x Area of brass= s x As
For the equilibrium of the system, compression in copper should be equal to tension in the steel
or
Load on the brass = Load on the steel
b x Ab = s x As
Also we know that,
actual expansion of steel = Actual expansion of brass (i)
But actual expansion of steel = Free expansion of steel + Expansion due to tensile stress in steel
And actual expansion of copper = Free expansion of copper - Contraction due to compressive
stress induced in brass
Substituting these values in equation (i), we get
Where T = Rise of temperature.
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 13
2.6 WORKED EXAMPLES
1) A metallic bar 300 mm x 100 mm x 40 mm is subjected to a force of 5 kN (tensile), 6 kN
(tensile) and 4 kN (tensile) along x, y and z directions respectively. Determine the change in
the volume of the block. Take E = 2 x 105
N/mm2
and Poisson's ratio = 0.25.
Solution:
Given: Dimensions of bar
= 300 mm x 100 mm x 40 mm
x = 300 mm, y = 100 mm and z = 40 mm
V= xyz = 300 x 100x40 = 1200000 mm3
Load in the direction of x=5KN; Load in the direction of y =6KN; Load in the direction of z =
4KN
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 14
2) A bar of 30 mm diameter is subjected to a pull of 60 kN. The measured extension on gauge
length of 200 mm is 0.1 mm and change in diameter is 0.004 mm. Calculate: (i) Young's
modulus, (ii) Poisson's ratio and (iii) Bulk modulus.
3) A rod is 2 m long at a temperature of 10°C. Find the expansion of the rod, when the
temperature is raised to 80°C. If this expansion is prevented, find the stress induced in the
material of the rod. Take E=1.0x 105
MN/m2
and  = 0.000012 per degree centigrade.
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 15
4) A steel rod of 20 mm diameter passes centrally through a copper tube of 50 mm external
diameter and 40 mm internal diameter. The tube is closed at each end by rigid plates of
negligible thickness. The nuts are tightened lightly home on the projecting parts of the rod. If
the temperature of the assembly is raised by 50°C, calculate the stresses developed in copper
and steel. Take E for steel and copper as 200 GN/m2
and 100 GN/m2
and  for steel and
copper as 12 x 10-6
per °C and 18 x 10-6
per °C.
As  for copper is more than that of steel, hence the free expansion of copper will be more than
that of steel when there is a rise in temperature. But the ends of the rod and the tube is fixed to
the rigid plates and the nuts are tightened on the projected parts of the rod. Hence the two
members are not free to expand. Hence the tube and the rod will expand by the same amount.
The free expansion of the copper tube will be more than the common expansion, whereas the free
expansion of the steel rod will be less than the common expansion. Hence the copper tube will be
subjected to compressive stress and the steel rod will be subjected to tensile stress.
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 16
Let s = Tensile stress in steel
 c = Compressive stress in copper.
For the equilibrium of the system,
Tensile load on steel = Compressive load on copper
…(i)
We know that the copper tube and steel rod will actually expand by the same amount. Actual
expansion of steel = Actual expansion of copper … (ii)
But actual expansion of steel
= Free expansion of steel + Expansion due to tensile stress in steel
and actual expansion of copper
= Free expansion of copper - Contraction due to compressive stress in copper
Substituting these values in equation (ii), we get
Mechanics of Materials 10ME34
Compiled by Hareesha N G, Asst Prof, DSCE Page 17
REFERENCES:
1) A Textbook of Strength of Materials By R. K. Bansal
2) Fundamentals Of Strength Of Materials By P. N. Chandramouli
3) Strength of Materials By B K Sarkar
4) Strength of Materials By R. K. Rajput

Weitere ähnliche Inhalte

Was ist angesagt? (20)

Bending stresses in beams
Bending stresses in beams Bending stresses in beams
Bending stresses in beams
 
Torsion of circular shafts
Torsion of circular shaftsTorsion of circular shafts
Torsion of circular shafts
 
Strength of Materials
Strength of MaterialsStrength of Materials
Strength of Materials
 
Riveted joints
Riveted jointsRiveted joints
Riveted joints
 
theories of failure
theories of failure theories of failure
theories of failure
 
Some basics of Strength Of Materials..
Some basics of Strength Of Materials..Some basics of Strength Of Materials..
Some basics of Strength Of Materials..
 
Strength of materials by A.Vinoth Jebaraj
Strength of materials by A.Vinoth JebarajStrength of materials by A.Vinoth Jebaraj
Strength of materials by A.Vinoth Jebaraj
 
Thermal stesses
Thermal stessesThermal stesses
Thermal stesses
 
Torsion
TorsionTorsion
Torsion
 
Basics of strength of materials
Basics of strength of materialsBasics of strength of materials
Basics of strength of materials
 
Thermal stress and strains
Thermal stress and strainsThermal stress and strains
Thermal stress and strains
 
Stress and strain- mechanics of solid
Stress and strain- mechanics of solidStress and strain- mechanics of solid
Stress and strain- mechanics of solid
 
Unit 1- simple stress and strain
Unit 1- simple stress and strainUnit 1- simple stress and strain
Unit 1- simple stress and strain
 
Unit 2 theory_of_plasticity
Unit 2 theory_of_plasticityUnit 2 theory_of_plasticity
Unit 2 theory_of_plasticity
 
Bending stresses in beams
Bending stresses in beamsBending stresses in beams
Bending stresses in beams
 
Sm 5
Sm 5Sm 5
Sm 5
 
Thin and thick cylinders
Thin and thick cylindersThin and thick cylinders
Thin and thick cylinders
 
Lecture 2 principal stress and strain
Lecture 2 principal stress and strainLecture 2 principal stress and strain
Lecture 2 principal stress and strain
 
Theories of Failures (STATIC LOADING)
Theories of Failures  (STATIC LOADING)Theories of Failures  (STATIC LOADING)
Theories of Failures (STATIC LOADING)
 
Lecture 1 stresses and strains
Lecture 1 stresses and strainsLecture 1 stresses and strains
Lecture 1 stresses and strains
 

Andere mochten auch

Andere mochten auch (14)

Cotter and knuckle joints
Cotter and knuckle jointsCotter and knuckle joints
Cotter and knuckle joints
 
Assembly of Machine vice
Assembly of Machine viceAssembly of Machine vice
Assembly of Machine vice
 
Unit 8: Torsion of circular shafts and elastic stability of columns
Unit 8: Torsion of circular shafts and elastic stability of columnsUnit 8: Torsion of circular shafts and elastic stability of columns
Unit 8: Torsion of circular shafts and elastic stability of columns
 
Assembly of Tail stock
Assembly of Tail stockAssembly of Tail stock
Assembly of Tail stock
 
Assembly of IC Engine Connecting rod
Assembly of IC Engine Connecting rodAssembly of IC Engine Connecting rod
Assembly of IC Engine Connecting rod
 
Mechanics of Materials: Question Bank from old VTU Question papers
Mechanics of Materials: Question Bank from old VTU Question papersMechanics of Materials: Question Bank from old VTU Question papers
Mechanics of Materials: Question Bank from old VTU Question papers
 
Orthographic projections
Orthographic projectionsOrthographic projections
Orthographic projections
 
Assembly of Ramsbottom safety valve
Assembly of Ramsbottom safety valveAssembly of Ramsbottom safety valve
Assembly of Ramsbottom safety valve
 
Computer aided machine drawing manual
Computer aided machine drawing manualComputer aided machine drawing manual
Computer aided machine drawing manual
 
Assembly of screw jack
Assembly of screw jackAssembly of screw jack
Assembly of screw jack
 
Assembly of Plummer block
Assembly of Plummer blockAssembly of Plummer block
Assembly of Plummer block
 
Section of solids
Section of solidsSection of solids
Section of solids
 
Riveted joints
Riveted jointsRiveted joints
Riveted joints
 
Unit 6: Bending and shear Stresses in beams
Unit 6: Bending and shear Stresses in beamsUnit 6: Bending and shear Stresses in beams
Unit 6: Bending and shear Stresses in beams
 

Ähnlich wie Unit 2 stresses in composite sections

Chapter ii tension & compression 1
Chapter ii tension & compression 1Chapter ii tension & compression 1
Chapter ii tension & compression 1MARTIN ATHIYO
 
mechanics of materials presentation - vtu
mechanics of materials presentation - vtumechanics of materials presentation - vtu
mechanics of materials presentation - vtuSuryaRS10
 
Physical state of the lithosphere
Physical state of the lithosphere Physical state of the lithosphere
Physical state of the lithosphere Cata R
 
LECTURE FOUR (02 MARCH 2023)-DELIVERED.pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED.pptxLECTURE FOUR (02 MARCH 2023)-DELIVERED.pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED.pptxthokomelomoloi
 
LECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptxLECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptxthokomelomoloi
 
Mechanical Behaviour of Materials Assignment Help
Mechanical Behaviour of Materials Assignment HelpMechanical Behaviour of Materials Assignment Help
Mechanical Behaviour of Materials Assignment HelpSolidwork Assignment Help
 
Som complete unit 01 notes
Som complete unit 01 notesSom complete unit 01 notes
Som complete unit 01 notessistec
 
ME 2213- Chapter-5 R.pptx
ME 2213- Chapter-5 R.pptxME 2213- Chapter-5 R.pptx
ME 2213- Chapter-5 R.pptxTurza
 
Stress & Strain PPT.ppt
Stress & Strain PPT.pptStress & Strain PPT.ppt
Stress & Strain PPT.pptBodhiSeal1
 
Stress & Strain PPT.ppt
Stress & Strain PPT.pptStress & Strain PPT.ppt
Stress & Strain PPT.pptBodhiSeal1
 
Strength of materials_I
Strength of materials_IStrength of materials_I
Strength of materials_IPralhad Kore
 

Ähnlich wie Unit 2 stresses in composite sections (20)

mechanics of solid
mechanics of solidmechanics of solid
mechanics of solid
 
Mm210(4)
Mm210(4)Mm210(4)
Mm210(4)
 
SImple strain.pdf
SImple strain.pdfSImple strain.pdf
SImple strain.pdf
 
Chapter ii tension & compression 1
Chapter ii tension & compression 1Chapter ii tension & compression 1
Chapter ii tension & compression 1
 
mechanics of materials presentation - vtu
mechanics of materials presentation - vtumechanics of materials presentation - vtu
mechanics of materials presentation - vtu
 
Physical state of the lithosphere
Physical state of the lithosphere Physical state of the lithosphere
Physical state of the lithosphere
 
LECTURE FOUR (02 MARCH 2023)-DELIVERED.pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED.pptxLECTURE FOUR (02 MARCH 2023)-DELIVERED.pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED.pptx
 
LECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptxLECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptx
LECTURE FOUR (02 MARCH 2023)-DELIVERED (1).pptx
 
Chap02-A.pdf
Chap02-A.pdfChap02-A.pdf
Chap02-A.pdf
 
Mos unit ii
Mos unit iiMos unit ii
Mos unit ii
 
Mos unit ii
Mos unit iiMos unit ii
Mos unit ii
 
Mechanical Behaviour of Materials Assignment Help
Mechanical Behaviour of Materials Assignment HelpMechanical Behaviour of Materials Assignment Help
Mechanical Behaviour of Materials Assignment Help
 
Som complete unit 01 notes
Som complete unit 01 notesSom complete unit 01 notes
Som complete unit 01 notes
 
Mm210(4b)
Mm210(4b)Mm210(4b)
Mm210(4b)
 
Simple stresses in machine parts
Simple stresses in machine partsSimple stresses in machine parts
Simple stresses in machine parts
 
2 axial loading
2 axial loading2 axial loading
2 axial loading
 
ME 2213- Chapter-5 R.pptx
ME 2213- Chapter-5 R.pptxME 2213- Chapter-5 R.pptx
ME 2213- Chapter-5 R.pptx
 
Stress & Strain PPT.ppt
Stress & Strain PPT.pptStress & Strain PPT.ppt
Stress & Strain PPT.ppt
 
Stress & Strain PPT.ppt
Stress & Strain PPT.pptStress & Strain PPT.ppt
Stress & Strain PPT.ppt
 
Strength of materials_I
Strength of materials_IStrength of materials_I
Strength of materials_I
 

Mehr von Hareesha N Gowda, Dayananda Sagar College of Engg, Bangalore

Mehr von Hareesha N Gowda, Dayananda Sagar College of Engg, Bangalore (20)

Alumni Meet Invitation.pdf
Alumni Meet Invitation.pdfAlumni Meet Invitation.pdf
Alumni Meet Invitation.pdf
 
Brammadevarahalli GP Panchapayana
Brammadevarahalli GP PanchapayanaBrammadevarahalli GP Panchapayana
Brammadevarahalli GP Panchapayana
 
Introduction to control systems
Introduction to control systemsIntroduction to control systems
Introduction to control systems
 
Be project report template
Be project report templateBe project report template
Be project report template
 
Dynamics of Machines: Question bank unitwise from vtu old question papers
Dynamics of Machines: Question bank unitwise from vtu old question papersDynamics of Machines: Question bank unitwise from vtu old question papers
Dynamics of Machines: Question bank unitwise from vtu old question papers
 
Robots: state of-the-art and future trends
Robots: state of-the-art and future trendsRobots: state of-the-art and future trends
Robots: state of-the-art and future trends
 
Screw thread measurements and Gear measurement
Screw thread measurements and Gear measurementScrew thread measurements and Gear measurement
Screw thread measurements and Gear measurement
 
Force, Pressure and Torque measurements
Force, Pressure and Torque measurementsForce, Pressure and Torque measurements
Force, Pressure and Torque measurements
 
Mechanical measurements and Measurement systems
Mechanical measurements and Measurement systemsMechanical measurements and Measurement systems
Mechanical measurements and Measurement systems
 
CIM and automation laboratory manual
CIM and automation laboratory manualCIM and automation laboratory manual
CIM and automation laboratory manual
 
Introduction to Non-Traditional Machining
Introduction to Non-Traditional MachiningIntroduction to Non-Traditional Machining
Introduction to Non-Traditional Machining
 
Chemical machining
Chemical machiningChemical machining
Chemical machining
 
Ultrasonic machining
Ultrasonic machiningUltrasonic machining
Ultrasonic machining
 
Introduction to Eddy Current Inspection
Introduction to Eddy Current InspectionIntroduction to Eddy Current Inspection
Introduction to Eddy Current Inspection
 
Magnetic Particle Inspection
Magnetic Particle InspectionMagnetic Particle Inspection
Magnetic Particle Inspection
 
Introduction to Ultrasonic Testing
Introduction to Ultrasonic TestingIntroduction to Ultrasonic Testing
Introduction to Ultrasonic Testing
 
Introduction to Radiographic Testing
Introduction to Radiographic TestingIntroduction to Radiographic Testing
Introduction to Radiographic Testing
 
Introduction to Non Destructive Testing
Introduction to Non Destructive TestingIntroduction to Non Destructive Testing
Introduction to Non Destructive Testing
 
Basic principles of CT scanning
Basic principles of CT scanningBasic principles of CT scanning
Basic principles of CT scanning
 
Acoustic Emission testing
Acoustic Emission testingAcoustic Emission testing
Acoustic Emission testing
 

Kürzlich hochgeladen

sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdfsdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdfJulia Kaye
 
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdfSummer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdfNaveenVerma126
 
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...Amil baba
 
EPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptxEPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptxJoseeMusabyimana
 
Guardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSecGuardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSecTrupti Shiralkar, CISSP
 
cloud computing notes for anna university syllabus
cloud computing notes for anna university syllabuscloud computing notes for anna university syllabus
cloud computing notes for anna university syllabusViolet Violet
 
ChatGPT-and-Generative-AI-Landscape Working of generative ai search
ChatGPT-and-Generative-AI-Landscape Working of generative ai searchChatGPT-and-Generative-AI-Landscape Working of generative ai search
ChatGPT-and-Generative-AI-Landscape Working of generative ai searchrohitcse52
 
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxSUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxNaveenVerma126
 
Mohs Scale of Hardness, Hardness Scale.pptx
Mohs Scale of Hardness, Hardness Scale.pptxMohs Scale of Hardness, Hardness Scale.pptx
Mohs Scale of Hardness, Hardness Scale.pptxKISHAN KUMAR
 
Engineering Mechanics Chapter 5 Equilibrium of a Rigid Body
Engineering Mechanics  Chapter 5  Equilibrium of a Rigid BodyEngineering Mechanics  Chapter 5  Equilibrium of a Rigid Body
Engineering Mechanics Chapter 5 Equilibrium of a Rigid BodyAhmadHajasad2
 
Modelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovationsModelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovationsYusuf Yıldız
 
IT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptxIT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptxSAJITHABANUS
 
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptxVertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptxLMW Machine Tool Division
 
Dev.bg DevOps March 2024 Monitoring & Logging
Dev.bg DevOps March 2024 Monitoring & LoggingDev.bg DevOps March 2024 Monitoring & Logging
Dev.bg DevOps March 2024 Monitoring & LoggingMarian Marinov
 
Basic Principle of Electrochemical Sensor
Basic Principle of  Electrochemical SensorBasic Principle of  Electrochemical Sensor
Basic Principle of Electrochemical SensorTanvir Moin
 
Phase noise transfer functions.pptx
Phase noise transfer      functions.pptxPhase noise transfer      functions.pptx
Phase noise transfer functions.pptxSaiGouthamSunkara
 
UNIT4_ESD_wfffffggggggggggggith_ARM.pptx
UNIT4_ESD_wfffffggggggggggggith_ARM.pptxUNIT4_ESD_wfffffggggggggggggith_ARM.pptx
UNIT4_ESD_wfffffggggggggggggith_ARM.pptxrealme6igamerr
 

Kürzlich hochgeladen (20)

sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdfsdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
sdfsadopkjpiosufoiasdoifjasldkjfl a asldkjflaskdjflkjsdsdf
 
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdfSummer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
 
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
 
EPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptxEPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptx
 
Guardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSecGuardians and Glitches: Navigating the Duality of Gen AI in AppSec
Guardians and Glitches: Navigating the Duality of Gen AI in AppSec
 
cloud computing notes for anna university syllabus
cloud computing notes for anna university syllabuscloud computing notes for anna university syllabus
cloud computing notes for anna university syllabus
 
Présentation IIRB 2024 Chloe Dufrane.pdf
Présentation IIRB 2024 Chloe Dufrane.pdfPrésentation IIRB 2024 Chloe Dufrane.pdf
Présentation IIRB 2024 Chloe Dufrane.pdf
 
Lecture 4 .pdf
Lecture 4                              .pdfLecture 4                              .pdf
Lecture 4 .pdf
 
ChatGPT-and-Generative-AI-Landscape Working of generative ai search
ChatGPT-and-Generative-AI-Landscape Working of generative ai searchChatGPT-and-Generative-AI-Landscape Working of generative ai search
ChatGPT-and-Generative-AI-Landscape Working of generative ai search
 
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxSUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
 
Mohs Scale of Hardness, Hardness Scale.pptx
Mohs Scale of Hardness, Hardness Scale.pptxMohs Scale of Hardness, Hardness Scale.pptx
Mohs Scale of Hardness, Hardness Scale.pptx
 
Engineering Mechanics Chapter 5 Equilibrium of a Rigid Body
Engineering Mechanics  Chapter 5  Equilibrium of a Rigid BodyEngineering Mechanics  Chapter 5  Equilibrium of a Rigid Body
Engineering Mechanics Chapter 5 Equilibrium of a Rigid Body
 
Modelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovationsModelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovations
 
IT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptxIT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptx
 
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptxVertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
Vertical- Machining - Center - VMC -LMW-Machine-Tool-Division.pptx
 
Dev.bg DevOps March 2024 Monitoring & Logging
Dev.bg DevOps March 2024 Monitoring & LoggingDev.bg DevOps March 2024 Monitoring & Logging
Dev.bg DevOps March 2024 Monitoring & Logging
 
Basic Principle of Electrochemical Sensor
Basic Principle of  Electrochemical SensorBasic Principle of  Electrochemical Sensor
Basic Principle of Electrochemical Sensor
 
Phase noise transfer functions.pptx
Phase noise transfer      functions.pptxPhase noise transfer      functions.pptx
Phase noise transfer functions.pptx
 
UNIT4_ESD_wfffffggggggggggggith_ARM.pptx
UNIT4_ESD_wfffffggggggggggggith_ARM.pptxUNIT4_ESD_wfffffggggggggggggith_ARM.pptx
UNIT4_ESD_wfffffggggggggggggith_ARM.pptx
 
計劃趕得上變化
計劃趕得上變化計劃趕得上變化
計劃趕得上變化
 

Unit 2 stresses in composite sections

  • 2. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 1 TABLE OF CONTENTS TABLE OF CONTENTS 0 Syllabus 2 2.1. VOLUMETRIC STRAIN 2 2.2. EXPRESSION FOR VOLUMETRIC STRAIN 2 2.3. ELASTIC CONSTANTS 4 2.3.1 Young’s Modulus 4 2.3.2 Shear Modulus or Modulus of Rigidity 5 2.3.3 Bulk modulus 5 2.3.4 Relation among Elastic Constants 6 i) Relation between E, G and  6 ii) Relation between E, K and : 8 iii) Relation between E, G and K 8 iv) Relation between E, K and  9 2.4. TEMPERATURE STRESSES 9 Stress and Strain when the Supports Yield: 10 2.5. THERMAL STRESSES IN COMPOSITE BARS 11 2.6 WORKED EXAMPLES 13 REFERENCES: 17
  • 3. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 2 UNIT 2: STRESS IN COMPOSITE SECTION Syllabus Volumetric strain, expression for volumetric strain, elastic constants, simple shear stress, shear strain, temperature stresses (including compound bars). 2.1. VOLUMETRIC STRAIN The ratio of change in volume to the original volume of a body (when the body is subjected to a single force or a system of forces) is called volumetric strain. It is denoted by εv. Mathematically, volumetric strain is given by V V v    Where δV = Change in volume, and V = Original volume. 2.2. EXPRESSION FOR VOLUMETRIC STRAIN Referring to Fig.2.1, the quantity εv represents the change in the volume per unit volume. It is referred to as the dilation of the material. Consider a small rectangular element of dimensions x, y and z subjected to three mutually perpendicular stresses. Fig. 2.1 Rectangular element subjected to three mutually perpendicular stresses. Original volume of the element is given by V = xyz Therefore, the total change in the volume
  • 4. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 3 or Referring to Fig.2.2, consider a bar/rod of length L and diameter d, then the volume of the bar is given by Fig.2.2. Volumetric strain in circular rod Therefore, Since V is the function of both d and L, dividing previous Eq. throughout by V, we get Since, We have, Thus, the volumetric strain is the sum of the three mutually perpendicular linear strains. Since εv represents a change in volume, it must be independent of the orientation of the element considered. It follows that the quantities,
  • 5. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 4 εx + εy + εz and ζx ζy and ζy are also independent of the orientation of the element. Since, εv = εx + εy + εz 2.3. ELASTIC CONSTANTS Elastic constants arc those factors which determine the deformations produced by a given stress system acting on a material. These factors (i.e. elastic constants) arc constant within the limits for which Hooke's laws are obeyed. Various elastic constants are:  Modulus of elasticity (E)  Poisson's ratio (μ or ν or 1/m)  Modulus of rigidity (G or N )  Bulk modulus (K) 2.3.1 Young’s Modulus When an axial stress σ (say, tensile) is applied along the longitudinal axis of a bar, the length of the bar will be increased. This change in the length (usually called deformation) per unit length of the bar, is termed as longitudinal strain (ε) or primary strain. This ratio of stress to strain, within elastic limits, is called the modulus of elasticity (E): Thus, modulus of elasticity (E) =ζ/ε The modulus of elasticity (also called Young's modulus of elasticity) is the constant of proportionality which is defined as the intensity of stress that causes unit strain. Table 2.1 gives the values of modulus of elasticity (E) for some common materials. S. N. Material Modulus of elasticity E (kN/mm2 or GPa) 1 Aluminium (Pure) 70 2 Aluminium alloys 70 - 79 3 Brass 96 - 110 4 Bronze 96-120 5 Cast iron 83 - 170 6 Copper (Pure) 110 - 120 7 Steel 190 - 210 8 Wrought iron 190
  • 6. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 5 2.3.2 Shear Modulus or Modulus of Rigidity The shear modules or modulus of rigidity (also called the modulus of transverse elasticity) expresses the relation between shear stress and shear strain. It has been found experimentally that, within elastic limit, shear stress (τ) is proportional to the shear strain (γ) Thus   G Where G = modulus of rigidity (Also sometimes denoted by symbol N or C) Table 2.2 gives the values of modulus of rigidity for some common engineering materials. Table 2.2. Values of modulus of rigidity S.N. Material Modulus of Rigidity (KNmm2 or GPa) 1 Aluminium (Pure) 26 2 Aluminium alloys 26-30 3 Brass 36-41 4 Bronze 36-44 5 Cast iron 32 - 69 6 Copper (Pure) 40-47 7 Steel 75-80 8 Wrought iron 75 2.3.3 Bulk modulus When a body is subjected to three mutually perpendicular like stresses of equal intensity (ζ), the ratio of direct stress (σ) to the corresponding volumetric strain (εv ) is defined as the bulk modulus K for the material of the body. Thus , v   strainVolumetric stressDirect =Kmodulusbulk The bulk modulus of elasticity K is defined only when three mutually perpendicular normal stresses are equal, i.e. σx = σy = σz = σ The bulk modulus of elasticity is shown in Fig. 2.3.
  • 7. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 6 Fig. 2.3: Bulk Modulus 2.3.4 Relation among Elastic Constants i) Relation between E, G and  Let us establish a relation among the elastic constants E, G and . Consider a cube of material of side ‘a' subjected to the action of the shear and complementary shear stresses as shown in the Fig. 2.4 and producing the strained shape as shown in the figure below. Assuming that the strains are small and the angle A C B may be taken as 450 . Fig. 2.4 Therefore strain on the diagonal OA = Change in length / original length Since angle between OA and OB is very small hence OA  OB therefore BC, is the change in the length of the diagonal OA
  • 8. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 7 Now this shear stress system is equivalent or can be replaced by a system of direct stresses at 450 as shown in Fig. 2.5. One set will be compressive, the other tensile, and both will be equal in value to the applied shear strain. Fig. 2.5 Thus, for the direct state of stress system which applies along the diagonals:
  • 9. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 8 ii) Relation between E, K and : Consider a cube subjected to three equal stresses  as shown in the Fig.2.6 Fig.2.6 The total strain in one direction or along one edge due to the application of hydrostatic stress or volumetric stress  is given as iii) Relation between E, G and K The relationship between E, G and K can be easily determined by eliminating  from the already derived relations. i.e., E = 2 G (1 + ) and E = 3 K (1  ) Thus, the following relationship may be obtained
  • 10. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 9 iv) Relation between E, K and  From the already derived relations, E can be eliminated 2.4. TEMPERATURE STRESSES Thermal stresses are the stresses induced in a body due to change in temperature. Thermal stresses are set up in a body, when the temperature of the body is raised or lowered and the body is not allowed to expand or contract freely. But if the body is allowed to expand or contract freely, no stresses will be set up in the body. Consider a body which is heated to a certain temperature. Let L = Original length of the body, T = Rise in temperature, E = Young's Modulus,  = Co-efficient of linear expansion, dL = Extension of rod due to rise of temperature. If the rod is free to expand, then extension of the rod is given by dL = .T.L This is shown in Fig. 2.7 (a) in which AB represents the original length and BB' represents the increase in length due to temperature rise. Now suppose that an external compressive load, P is applied at B' so that the rod is decreased in its length from (L + .T.L) to L as shown in Figs. (b) and (c).
  • 11. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 10 Fig. 2.7: Thermal stresses And load or thrust on the rod = Stress x Area = .T.E x A If the ends of the body are fixed to rigid supports, so that its expansion is prevented, then compressive stress and strain will be set up in the rod. These stresses and strains are known as thermal stresses and thermal strain. Thermal stress is also known as temperature stress. And thermal strain is also known as temperature strain. Stress and Strain when the Supports Yield: If the supports yield by an amount equal to , then the actual expansion = Expansion due to rise in temperature -  = .T.L - 
  • 12. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 11 2.5. THERMAL STRESSES IN COMPOSITE BARS Fig. 2.8 (a) shows a composite bar consisting of two members, a bar of brass and another of steel. Let the composite bar be heated through some temperature. If the members are free to expand then no stresses will be induced in the members. But the two members are rigidly fixed and hence the composite bar as a whole will expand by the same amount. As the co-efficient of linear expansion of brass is more than that of the steel, the brass will expand more than the steel. Hence the free expansion of brass will be more than that of the steel. But both the members are not free to expand, and hence the expansion of the composite bar, as a whole, will be less than that of the brass, but more than that of the steel. Hence the stress induced in the brass will be compressive whereas the stress in steel will be tensile as shown in Fig. 2.8 (c). Hence the load or force on the brass will be compressive whereas on the steel the load will be tensile. Let Ab = Area of cross-section of brass bar σb = Stress in brass b = Strain in brass b = Co-efficient of linear expansion for brass Eb = Young’s modulus for copper As, s, s, s = Corresponding values of area, stress, strain and co-efficient of linear expansion for steel, and Es = Young's modulus for steel.  = Actual expansion of the composite bar
  • 13. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 12 Now load on the brass = Stress in brass x Area of brass= b x Ab And load on the steel = Stress in brass x Area of brass= s x As For the equilibrium of the system, compression in copper should be equal to tension in the steel or Load on the brass = Load on the steel b x Ab = s x As Also we know that, actual expansion of steel = Actual expansion of brass (i) But actual expansion of steel = Free expansion of steel + Expansion due to tensile stress in steel And actual expansion of copper = Free expansion of copper - Contraction due to compressive stress induced in brass Substituting these values in equation (i), we get Where T = Rise of temperature.
  • 14. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 13 2.6 WORKED EXAMPLES 1) A metallic bar 300 mm x 100 mm x 40 mm is subjected to a force of 5 kN (tensile), 6 kN (tensile) and 4 kN (tensile) along x, y and z directions respectively. Determine the change in the volume of the block. Take E = 2 x 105 N/mm2 and Poisson's ratio = 0.25. Solution: Given: Dimensions of bar = 300 mm x 100 mm x 40 mm x = 300 mm, y = 100 mm and z = 40 mm V= xyz = 300 x 100x40 = 1200000 mm3 Load in the direction of x=5KN; Load in the direction of y =6KN; Load in the direction of z = 4KN
  • 15. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 14 2) A bar of 30 mm diameter is subjected to a pull of 60 kN. The measured extension on gauge length of 200 mm is 0.1 mm and change in diameter is 0.004 mm. Calculate: (i) Young's modulus, (ii) Poisson's ratio and (iii) Bulk modulus. 3) A rod is 2 m long at a temperature of 10°C. Find the expansion of the rod, when the temperature is raised to 80°C. If this expansion is prevented, find the stress induced in the material of the rod. Take E=1.0x 105 MN/m2 and  = 0.000012 per degree centigrade.
  • 16. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 15 4) A steel rod of 20 mm diameter passes centrally through a copper tube of 50 mm external diameter and 40 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projecting parts of the rod. If the temperature of the assembly is raised by 50°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m2 and 100 GN/m2 and  for steel and copper as 12 x 10-6 per °C and 18 x 10-6 per °C. As  for copper is more than that of steel, hence the free expansion of copper will be more than that of steel when there is a rise in temperature. But the ends of the rod and the tube is fixed to the rigid plates and the nuts are tightened on the projected parts of the rod. Hence the two members are not free to expand. Hence the tube and the rod will expand by the same amount. The free expansion of the copper tube will be more than the common expansion, whereas the free expansion of the steel rod will be less than the common expansion. Hence the copper tube will be subjected to compressive stress and the steel rod will be subjected to tensile stress.
  • 17. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 16 Let s = Tensile stress in steel  c = Compressive stress in copper. For the equilibrium of the system, Tensile load on steel = Compressive load on copper …(i) We know that the copper tube and steel rod will actually expand by the same amount. Actual expansion of steel = Actual expansion of copper … (ii) But actual expansion of steel = Free expansion of steel + Expansion due to tensile stress in steel and actual expansion of copper = Free expansion of copper - Contraction due to compressive stress in copper Substituting these values in equation (ii), we get
  • 18. Mechanics of Materials 10ME34 Compiled by Hareesha N G, Asst Prof, DSCE Page 17 REFERENCES: 1) A Textbook of Strength of Materials By R. K. Bansal 2) Fundamentals Of Strength Of Materials By P. N. Chandramouli 3) Strength of Materials By B K Sarkar 4) Strength of Materials By R. K. Rajput