it is a brief introductory part of what is house drainage system , its components with their classification , types of system of plumbing aided with principles of drainage design.
2. Semester : 5th Civil-A
Subject :
Code : 2150603
Presentation On :
Prepared by : Eddy Ankit Gangani
eddygangani@gmail.com
3. Introduction
Basic Terminology
Principles of House Drainage System
Components of House Drainage System
- Pipes
- Traps
- Sanitary Fittings
System Of Plumbing
House Drainage Plan
4. What is House + Drainage + System ?
Why House Drainage System is used ?
What are the Components of House
Drainage System ?
6. Lay sewers by the side of building
Properly ventilated
Enough number of traps
Watertight joints
Proper gradient
Flow under Gravity
Easy cleaning , repair & maintenance
Straight drains
Rain water pipe
Anti siphonage pipe
7. Components of house drainage system
TrapsPipes Sanitary
fittings
According to
Use
P – Trap
Q – Trap
S - Trap
Floor Trap
Gully Trap
Grease Trap
Intercepting Trap
According to
shape
8. Sanitary
fittings
Pipes Traps
Components of house drainage system
Washbasin
Sink
Bathtub
WC
Urinal
Flushing
Cistern
Soil Pipe
Vent Pipe
Waste Pipe
Rain Pipe
Antisiphonage
Pipe
10. (1) Floor Trap
To admit sullage
from floors ,
bathroom , kitchen
etc.
Material : Cast iron
, stainless steel,
galvanized gratings
No blockage,
starting point of
waste water flow.
A.K.A. “Nahni Trap”
11. (2) Gully Trap
Provided at junction of a roof
drain & other drain from kitchen
or bath.
A gully trap is usually made of
stoneware and a C.I. grating is
provided at its top.
a water seal of 50 to 75 mm
12. (3) Intercepting Trap
Provided at junction of a
house sewer & municipal
sewer or septic tank
Provided in the last
manhole of the house
drainage system
To prevent entry of foul
gases in the public sewer
to house drainage.
A.K.A. disconnecting trap
or Interceptor trap
13. Advantages & disadvantages Intercepting Trap
Restricts entry of
foul gases of public
sewer line.
Harmful pathogens
are not entered in
house drains.
Make access for the
cleaning and removal
of the debris and
garbage
Retentions of heavy
particles causes
decomposition & foul
gases are produced
Cleaning is difficult
Interceptor may be an
obstruction
If lead or plug is not
tightened the foul gases
from public sewer will
enter the house drain
14. (4) Grease Trap
Used where large quantity of
oily waste is generated
To prevent ugly scum &
blockages to re-aeration.
It’s a masonry or cast iron
chamber with a bent pipe or
Tee –pipe at the outlet end
15. Waste Pipe : Pipe carrying
sullage
Soil Pipe : Pipe carrying
sewage
Vent pipe : Pipe installed for
the purpose of ventilation or
to carry foul smell
Rain Water Pipe : Pipe carrying
rain water
Antisiphonage Pipe : Maintains
proper ventilation and does
not allow the siphonic action
to take place
Types of Pipes
16. Components of Sanitary fittings
(1) Wash Basin
Used for washing hands,brush
Materials : Porcelain,
: Stainless steel,
: Plastic
Angle Back Pattern
Size
600*480mm
400*400mm
Flat Back Pattern
Size
630*450mm
550*400mm
450*300mm
17. Components of Sanitary fittings
(2) Sinks
Normally rectangular basin used in kitchen or laboratory
for cleaning utensils and glasswares.
Made of glazed earthware, stainless steel or enameled
pressed steel.
18. Components of Sanitary fittings
(3) Bathtubs
For long and luxurious bath
Made of iron or steel coated with enamel,enameled
porcelain or of plastic
It is provided with outlets and outflow pipes,usually 40mm
diameter.
Conventional sizes of bathtub:
– Length 1.7 to 1.85 m
– Width 0.7 to 0.75 m
- Depth 0.6m
19. Components of Sanitary fittings
(4) Water Closets
designed to receive human excreta directly and convey to the
septic tank or underground sewer through a trap
Indian Type Europian Type
Anglo-Indian
Type
20. Components of Sanitary fittings – W.C.
(1) Indian Type W.C.
– Simple in construction
– Used in squatting (siting) position.
– Made of porcelain
– The pan and trap are available as
two separate pieces
– Closet is setup at the floor level
and pair of foot rests are provided
on both side of the pan.
– The length of pan varies from
450mm to 675 mm and water seal
varies from 50mm to 75mm
21. Components of Sanitary fittings – W.C.
(2) Europian Type W.C.
– Usually made of porcelain
– Pan has a flushing rim to spread the
flush water
– The closet is either fitted with P or S
trap.
– Can also be used at upper floors, while
in case of Indian type W.C. the upper floor
has to be depressed to receive the pan
fixed at floor level.
– The length of pan varies from 500 to
600mm and depth varies from 350mm to
400mm
22. Components of Sanitary fittings – W.C.
(3) Anglo-Indian Type W.C.
– Main advantage of Indian W.C. is that it
can be used in squatting position since it
is fixed at floor
level.
– While in European W.C. which is fixed
at about 400mm above floor level can
not be conveniently used in squatting
position.
– Here closet is fixed 400mm above the
floor level.
– The top flushing rim and seat etc. are
similar to European type.
23. Components of Sanitary fittings
(4) Urinals
Bowl Type Urinals
Stall Type Urinals
Angle Back Pattern
340*430*265
Flat Back Pattern
430*260*350mm
24. The contents of urinals are collected and
discharged in to the soil pipe through floor trap
(nahni trap).
Automatic flushing cistern are generally provided
for stall type urinals which operates at regular
interval of 10 to 15 minutes.
• A stall type urinal normally has more than one
units, with a centre to centre spacing of 0.6 to
0.7m.
• IS 2556 part 6-1992 describes the detailed
specifications for the various vitreous urinals
25. Components of Sanitary fittings Urinals
Flushing Cistern
Valve less siphonic
type (Bell type
cistern)
Valve fitted
siphonic type (A
float type)
26. • Single stack system
• One pipe system
• Partially ventilated single stack system
• Two pipe system